Anhui Star Control Instrument Co., Ltd.

Anhui Star Control Instrument Co., Ltd.

  • 100MM flange fixed shockproof pressure gauge
  • 100MM flange fixed shockproof pressure gauge

100MM flange fixed shockproof pressure gauge

  • Product Item:100MM flange fixed shockproof pressure gauge
  • Category:Shockproof pressure gauge
  • Views:382
  • Product Manual:100MM flange fixed shockproof pressure gauge,Pressure gauge, barometer, stainless steel pressure gauge, CNG sensor, CNG pressure gauge, bimetal thermometer, medical pressure gauge, pressure reducer, d
BASIC INFO

The oil-filled seismic pressure gauge relies on internal glycerin (or silicone oil) and is equipped with cushioning screws.In order to overcome the damage caused by strong vibration of the environment and strong pulsation of the medium to ensure the measurement accuracy, the instrument is suitable for measuring the pressure of various gases and liquids in places where the medium pressure is strong and mechanical vibration.
Third, the applicable occasions:
The oil-filled earthquake-resistant pressure gauge is suitable for places with severe environmental vibration, and can withstand the pulsation, impact and sudden unloading of the medium, and the instrument indication is stable and clear.It is widely used in machinery, petroleum, chemical, metallurgy, mining, electric power and other departments to measure the pressure on copper and copper alloy non-corrosive media.

Fourth, the performance characteristics:
1. The performance is stable, the measurement accuracy is high, and the reaction speed is fast.
2. The total pressure is measured, including the pressure of gas and steam.
3. The measured results are independent of the gas type, composition and properties.
4. During the pressure measurement process, the pressure gauge itself has little inspiration and deflation, and will not affect the measured air pressure.
5. There are no high temperature parts inside, which will not decompose oil vapor.
6. If corrosive materials are used, the corrosive gas pressure can be measured.
7, the structure is firm, and easy to seal and install.
8, easy to operate, no need to adjust, but need to be verified regularly.

V. Technical indicators:

model

YTN-40B

YTN-50B

YTN-60B

YTN-75B

YTN-100B

YTN-150B

Nominal diameter (mm)

¢40

¢50

¢60

¢75

¢100

¢150

Joint thread

M10×1;M14×1.5;M20×1.5;G1/4;G3/8;G1/2;

Accuracy level (%)

2.5

1.6

Range (Mpa)

-0.1~0;-0.1~0.06;-0.1~0.15;-0.1~0.3;-0.1~0.5;-0.1~0.9;-0.1~1.5;-0.1~2.4;

0~0.1;0~0.16;0~0.25;0~0.4;0~0.6;0~1.0;0~1,6;0~2.5;0~4.0;0~6.0;0~10;0~16;0~25;0~40;0~60;0~100;0~160;

Ambient temperature (°C)

-40~70

structure type

Radial borderless; axial without edge (z); axial with leading edge (zq)

Radial belt trailing edge (t); radial belt leading edge (tq); clamp mounting (u)

Seismic rating

V.H.4

Executive standard

GB/T1226-2001

Protection level

IP54

Case material

304SS

Joint material

304SS;316;316L

Sixth, the size:

model

Dimensions mm

A

B

C

D

d

d0

M

YN-50Z

29

24

0

50

/

/

14X1.5

YN-60

31

32

14

60

/

/

YN-60T

31

32

15

75

3.4

YN-60Z

30

32

0

/

/

YN-60ZQ

30

32

0

75

3.4

YN-75

24

30

12

75

/

/

YN-75T

24

30

12

90

5.5

YN-75Z

24

30

0

/

/

YN-75ZQ

24

30

0

90

5.5

YN-100

44

45

18

100

/

/

20X1.5

YN-100T

44

46

19

118

5.5

YN-100Z

43

45

34

/

/

YN-100ZQ

43

45

44

118

5.5

YN-150

50

47

19

149

/

/

20X1.5

YN-150T

50

48

20

165

5.5

YN-150Z

51

47

55

/

/

YN-150ZQ

51

47

55

165

5.5

Note: Connection thread can be ordered as required

7. Regular maintenance and repair:
1. After a period of use and pressure, the pressure gauge movement will inevitably have some deformation and wear, and the pressure gauge will produce various errors and malfunctions.In order to ensure its original accuracy without distorting the magnitude, it should be replaced in time to ensure that the instructions are correct, safe and reliable.
2. The pressure gauge should be cleaned regularly.Because the inside of the pressure gauge is not clean, it will increase the wear of each machine, which will affect its normal work, and will seriously cause the pressure gauge to fail and be scrapped.
3. The pressure gauge installed at the pressure measuring part, according to the provisions of jjg52-1999, its verification period generally does not exceed half a year.
4. The medium of the pressure measuring part has large fluctuation, frequent use, high accuracy requirement, and strict requirements on safety factors. The verification period can be shortened according to the specific situation.

Eight, installation notes:
1. The ambient temperature of the instrument is -40~70°C, the relative humidity is not more than 80%. If it deviates from the normal use temperature by 20±5°C, the temperature additional error must be included.
2. The instrument must be installed vertically, and strive to maintain the same level with the measuring point. If the difference is too high, the additional error caused by the liquid column is not necessary.When installing, block the explosion-proof port at the back of the case to avoid affecting the explosion-proof performance.
3. The measuring range of the normal use of the instrument: 3/4 of the upper limit of the measurement under static pressure, and should not exceed 2/3 of the upper limit of measurement under fluctuation.Under the above two pressure conditions, the large pressure gauge should not be lower than 1/3 of the lower limit, and the vacuum part should be used when measuring vacuum.
4. In case of failure when the instrument pointer fails or the internal parts are loose and cannot work normally, it should be repaired or repaired by the manufacturer.
5. The instrument should avoid vibration and collision to avoid damage.

Nine, selection list:

Ten, use and ordering instructions:
1. In use, because the ambient temperature is too high, the meter indication value does not return to zero position. A fine needle can be used to pass a small hole in the rubber plug of the meter to make the inner cavity of the meter pass through the atmosphere.
2. The working environment should be free from corrosive gases.

The oil-filled seismic pressure gauge relies on internal glycerin (or silicone oil) and is equipped with cushioning screws.In order to overcome the damage caused by strong vibration of the environment and strong pulsation of the medium to ensure the measurement accuracy, the instrument is suitable for measuring the pressure of various gases and liquids in places where the medium pressure is strong and mechanical vibration.
Third, the applicable occasions:
The oil-filled earthquake-resistant pressure gauge is suitable for places with severe environmental vibration, and can withstand the pulsation, impact and sudden unloading of the medium, and the instrument indication is stable and clear.It is widely used in machinery, petroleum, chemical, metallurgy, mining, electric power and other departments to measure the pressure on copper and copper alloy non-corrosive media.

Fourth, the performance characteristics:
1. The performance is stable, the measurement accuracy is high, and the reaction speed is fast.
2. The total pressure is measured, including the pressure of gas and steam.
3. The measured results are independent of the gas type, composition and properties.
4. During the pressure measurement process, the pressure gauge itself has little inspiration and deflation, and will not affect the measured air pressure.
5. There are no high temperature parts inside, which will not decompose oil vapor.
6. If corrosive materials are used, the corrosive gas pressure can be measured.
7, the structure is firm, and easy to seal and install.
8, easy to operate, no need to adjust, but need to be verified regularly.

V. Technical indicators:

model

YTN-40B

YTN-50B

YTN-60B

YTN-75B

YTN-100B

YTN-150B

Nominal diameter (mm)

¢40

¢50

¢60

¢75

¢100

¢150

Joint thread

M10×1;M14×1.5;M20×1.5;G1/4;G3/8;G1/2;

Accuracy level (%)

2.5

1.6

Range (Mpa)

-0.1~0;-0.1~0.06;-0.1~0.15;-0.1~0.3;-0.1~0.5;-0.1~0.9;-0.1~1.5;-0.1~2.4;

0~0.1;0~0.16;0~0.25;0~0.4;0~0.6;0~1.0;0~1,6;0~2.5;0~4.0;0~6.0;0~10;0~16;0~25;0~40;0~60;0~100;0~160;

Ambient temperature (°C)

-40~70

structure type

Radial borderless; axial without edge (z); axial with leading edge (zq)

Radial belt trailing edge (t); radial belt leading edge (tq); clamp mounting (u)

Seismic rating

V.H.4

Executive standard

GB/T1226-2001

Protection level

IP54

Case material

304SS

Joint material

304SS;316;316L

Sixth, the size:

model

Dimensions mm

A

B

PREVIOUS:100MM upright shockproof pressure gauge
NEXT:Browse Product

Online Inquiry


Deutsch Espanol Francais Italiano Portugues Japanese Korean Arabic Russian
X

 Sent email